Open Jobs

Trillium Construction is seeking NCCER/NCCCO Riggers near Temple, TX.Key ResponsibilitiesRig, lift, move, and position 168 chillers weighing approximately 22,000 lbs. each.Work with a rigging crew to safely manage 32 rigging points per chiller.Inspect and properly use slings, shackles, spreader bars, chain falls, hoists, and other rigging equipment.Follow approved lift plans, rigging procedures, and site safety requirements.Communicate clearly with crane operators, signal persons, foremen, and other members of the rigging crew.Guide and control loads during lifting, setting, alignment, and final positioning.Maintain proper exclusion zones and ensure personnel remain clear of suspended loads.Schedule: Mon - Sat, 60h / week, 6a to 4p

Trillium Construction is now hiring Sheet Metal Mechanics in Vicksburg, MS!Will be working on commercial project, hanging duct and putting in welding booths at a community college.Schedule: Mon-Sat, 50-58 hrs/week

Seeking Journeyman Millwrights with paper mill experience for a 10- to 12-day shutdown in Franklin, Virginia STARTING 9/02!!!!!Start Date: September 2Schedule: Night Shift, 7:00 PM - 7:00 AM; 80+ HOURS/WEEKDuration: 10-12 daysScope of Work: Work will primarily involve equipment change-outs on the feed side of the mill, including outlet devices, high-pressure and low-pressure feeders, airlock screws, and other mechanical equipment.Transportation: Bus transportation will be provided from a designated parking area.Mileage: Paid for travel over 50 miles from the employee's driver's license address.

STRUCTURAL MIG WELDERS NEEDED IN HOUSTON, TX!!Position: Structural MIG Welder - BESS Storage Housing CabinetsResponsibilities & RequirementsFabricate and weld steel Battery Energy Storage System (BESS) housing cabinets.Welders will be working primarily with 3/8-inch steel and will be responsible for structural welding and fabrication workAll MIG weldingMust be able to pass basic weld test on site - test info pending and pre-employment screenings.Schedule: Mon - Fri 10-12hr days.Project Duration - Initial assignment: 8 weeks

Trillium Construction is seeking night and day shift Certified Riggers for a project in Red Oak, TX. Riggers are needed to support the indoor installation of electrical equipment inside a data center. This role involves precision rigging and material handling using specialized moving systems to safely position and install critical infrastructure components.All work is performed in controlled indoor facilities with strict safety, quality, and cleanliness standards.Primary ResponsibilitiesRig, move, and position electrical equipment, pallets, and modules inside the data centerPerform precision placement of equipment using:SkatesHydraulic jacksForkliftsMan-Genie liftsRotating telehandlersAlign, level, and set equipment to installation tolerancesCoordinate movements with team members and supervisorsFollow lift plans, move plans, and manufacturer requirementsProtect sensitive electrical equipment and finished surfacesMaterial Handling & Facility SupportStage, organize, and store modules for future installationLoad and unload materials for transport to and from work areasMaintain clear and organized work zones inside the facilitySupport logistics and material flow within the data centerRigging Equipment UsedNylon slingsSteel chokersShacklesSpreader barsSkates and jacking systemsSpecialized lifting and positioning devicesAdditional DutiesInspect rigging equipment before and after useIdentify and report damaged or non-compliant gearAssist with module positioning for staging or storageSupport warehouse, yard, and indoor logistics operationsMaintain housekeeping and cleanliness standardsSchedule: Mon - Fri, 50h / week

In need of apprentice electricians for a 5 month long project in Fort Morgan, CO working on a substation/solar/battery storage project starting 8/10.Project DetailsWill be working on a substation/solar/battery storage projectWorking 50hr weeks Monday-Friday5 month long job

Tradesmen International is immediately hiring experienced Structural Steel Welders for projects located in or around Olean, NY. This is a first shift opportunity. If you are a Licensed Journeyman Electrician and want to work alongside other proven craftsmen who emphasize safety, productivity, and superior craftsmanship, this is your chance to advance your career!Job ScopeWeld large-diameter pipe in accordance with AWS D1.1 Structural Welding CodePerform FCAW (Flux Core Arc Welding) on heavy structural steel componentsComplete multipass groove welds and CJP (Complete Joint Penetration) weldsRead and interpret fabrication drawings, blueprints, and welding symbolsEnsure all welds meet quality and structural specificationsAssist with rigging and material handling as neededWork safely in a structural steel fabrication shop environment

Journeyman Electricians - Immediate Openings | Southaven, MSNCW is hiring Journeyman Electricians for an immediate opportunity in Southaven, MS on a Power Distribution Facility project.Position DetailsPosition: Journeyman ElectricianLocation: Southaven, MSProject: Power Distribution FacilityShift: Night ShiftSchedule: 7 Days per Week, 12-Hour ShiftsDuration: Approximately 6-8 MonthsResponsibilitiesInstall, terminate, and test electrical systems and equipment.Read and interpret blueprints and electrical drawings.Perform electrical work in accordance with project specifications and code requirements.Maintain a safe and productive work environment.

Journeyman ElectricianLocation: Reno, NVSchedule: Monday - Saturday, 10-hour shiftsDuration: Long-Term Project (6+ Months)Job OverviewWe are currently seeking experienced Journeyman Electricians with strong industrial and commercial controls experience for a long-term construction project in Reno, Nevada. Candidates must have hands-on experience installing, wiring, troubleshooting, and maintaining motor control systems and electrical control equipment in industrial or large-scale commercial environments.This position offers consistent overtime, competitive pay, and per diem for qualified travelers. Electricians will work alongside other skilled trades to support the installation and commissioning of electrical systems, motor controls, and process equipment.ResponsibilitiesInstall, wire, terminate, and troubleshoot motor control circuits and electrical equipment.Install and maintain motor starters, contactors, overload relays, and disconnects.Install, wire, and troubleshoot Variable Frequency Drives (VFDs) and soft starters.Assemble, wire, and test electrical control panels and Motor Control Centers (MCCs).Read and interpret electrical blueprints, schematics, one-line diagrams, and control drawings.Pull wire, install conduit (EMT, rigid, PVC), and perform cable tray installations.Perform equipment startup, testing, and commissioning activities.Troubleshoot electrical and control system issues using meters and diagnostic equipment.Install and terminate low-voltage and control wiring for industrial systems and equipment.Ensure all work is completed in compliance with NEC standards, project specifications, and safety regulations.Coordinate with project supervisors, engineers, and other trades to maintain project schedules.Maintain a clean, organized, and safe work environment.

Superior Skilled Trades is seeking Commercial Plumbers for an immediate start through Central and North Iowa!NO INTERVIEW NEEDED, TEMP-TO-HIRE OPPORTUNITY, PER DIEM AVAILABLE FOR TRAVELERS!Position DetailsHours: 8-hour workdays (40 hours/week)Schedule: Monday-Friday; 6:00 AM - 2:30 PM - 40 hours a week no overtime.Start Date: ASAPDuration: Temp-to-HireCommercial Plumber Job DescriptionSuperior Skilled Trades is hiring experienced Commercial Plumbers to install, repair, and maintain plumbing systems on commercial construction projects. Responsibilities include installing mechanical piping, drainage systems, fixtures, valves, fittings, and associated equipment while ensuring all work complies with the Uniform Plumbing Code and project specifications. Candidates must be able to read and interpret blueprints, submittals, and specifications, plan daily tasks, and work independently or with a crew to complete projects safely and efficiently.

Trillium Construction is looking for Iron Workers in Brownsville,TX asap!Erect and install structural steel, beams, columns, braces, platforms, stairs, handrails, ladders, and support frames.Read and interpret structural drawings, blueprints, erection plans, weld maps, and rigging plans.Connect steel members using high-strength bolts, pins, welds, and other approved fastening methods.Work at heights using aerial lifts, elevated work platforms, and fall-protection systems.Perform steel fit-up, alignment, leveling, plumb-up, and dimensional adjustments.Work outdoors in demanding conditions and around large-scale construction equipment.

HIRING JOURNEYMAN MILLWRIGHTS IN CLINTON, IA ASAP!!!Plant maintenance at Ingredient plant2 week long project working 7 12'sDuties include cutting, grinding, and demoing equipment. MUST BE ABLE TO BOLT UP & CONNECT

Trillium Construction is seeking Millwrights for a project in Red Oak, TX.Key ResponsibilitiesMaterial Handling: Unload materials and equipment from trucks using forklifts, pallet jacks, and rigging gear.Skating, rigging, and moving materials and equipment safely throughout the site.Stage and organize equipment and materials for installation.Equipment & System Installation: Assist in setting and installing mechanical equipment, racks, and server infrastructure.Use hoists, dollies, rollers, and other rigging devices to position equipment.Perform bolt-up work on structural and mechanical systems.Install and align piping systems (minor pipefitting as required).Tools & Machinery: Operate forklifts, telehandlers, and other powered industrial trucks as needed.Use hand and power tools such as torque wrenches, impact guns, levels, and alignment tools.Safety & Quality: Follow all site safety rules, policies, and procedures.Participate in daily safety meetings and job hazard analyses.Ensure quality workmanship and proper installation per drawings and specifications.

Trillium Construction is seeking Instrumentation Techs near Lincoln, NE to install Rosemount pressure, temperature and level transmitters (approximately 15-20 instruments in total). Mechanical installation only - no wiring involved.May need assistance with installing instrument air and nitrogen lines which will be compromised of Viega MegaPress fittings and stainless steel piping. This will be working in a gas upgrading facility in Lincoln NE, though no gas will be present.

Journeyman & Helper Sheet Metal Mechanics | Richmond, VAProject Duration: 1 yr. + projectProject Type: Commercial Data Center ConstructionJob OverviewKodiak Labor Solutions is seeking experienced Sheet Metal Mechanics at the Journeyman and Helper levels for a large scale commercial data center project in the Richmond, Virginia area.Both local and traveling candidates are encouraged to apply, with $120/day per diem available for qualified travelers. This is a 1 yr. + project opportunity for sheet metal professionals with hands-on experience fabricating, installing, and hanging commercial ductwork.What You'll DoAs a Sheet Metal Mechanic, you'll work as part of an active construction crew installing and supporting ductwork systems throughout the data center project.Responsibilities include:Fabricate, install, and hang sheet metal ductwork according to project drawings and specificationsRead and interpret mechanical drawings, blueprints, layouts, and installation documentationMeasure, fit, and assemble ductwork and related sheet metal componentsCoordinate with crew members and supervision to maintain installation schedules and project timelinesMaintain tools and equipment in accordance with jobsite and safety standardsFollow all site specific safety procedures and requirementsCommunicate installation issues, delays, and progress to the crew lead or foreman

Location: Liberty Steel, Peoria, ILSchedule: 2 Weeks working 7/12’s Beginning 8.17.26The Systems Group is looking for an energetic individual to be our next Structural Welder. We are looking for someone to help with the day-to-day issues that pop up but also to be part of the big picture and contribute to the long-term strategy of our operations across the country.Structural Welder Job Responsibilities:Layout, fabrication, and assembly of angle iron, I-beams, and various other shaped metalsRepair products by dismantling, straightening, reshaping, and reassembling parts using a cutting torch, straightening press, and other hand tools.

Location: Liberty Steel – Peoria, ILSchedule: 7/12’s – Duration of 2 weeks beginning 8.17.26The Systems Group is looking for an energetic individual to be our next Pipefitter. We are looking for someone to help with the day-to-day issues that pop up but to also be part of the big picture and contribute to the long-term strategy of our operations across the country.Pipefitter Job Responsibilities:Selects the type and size of pipe and related materials and equipment, such as supports, hangers, and hydraulic cylinders, according to job specifications.Inspects the worksite to determine the presence of obstructions.Plans sequence on installation to avoid obstructions and activities of other workers.Cuts pipe using a reciprocating saw, pipe cutter, cutting torch and pipe cutting machine, and/or other small hand tools.Threads pipe using a threading machine.Bends pipe by hand or with pipe-bending tools and machines.Mounts pipe hangers and brackets on walls and ceiling to hold pipe.Assembles and installs a variety of metal or nonmetal pipes and pipe fittings.Secures pipes to structure with brackets, clamps, and hangers, using hand and power tools.Performs minor maintenance of cleaning activities of tools and equipment.Observes and comply with all safety and project rules and all company policies and proceduresPerforms other duties as required.

Location: Liberty Steel – Peoria, ILSchedule: 2 Weeks Beginning 8.17.26The Systems Group is looking for an energetic individual to be our next Skilled Helper teammate. We are looking for someone to help with the day-to-day issues that pop up but to also be part of the big picture and contribute to the long-term strategy of our operations across the country.Skilled Helper Job Responsibilities:Clean work areaRestock supplies and materialsAssist with lifting, positioning, and securing of materials and workpiecesDisassemble and remove damaged materials from the work areaAssist journeyman employees with task-related to pipefitting or weldingUse power tools when applicable

Plumbers Needed | Data Center Project | Richmond, VAJob OverviewKodiak Labor Solutions is seeking Plumbers at the Journeyman and Helper levels for a data center construction project in Richmond, Virginia running 6+ months. Both local and traveling candidates are encouraged to apply, with $120/day per diem available for qualified travelers.What You'll DoInstall, assemble, and support copper ProPress and PVC piping systemsPerform ProPress connections on copper pipingInstall water, gas, and drainage piping systems as requiredRead and interpret blueprints, mechanical drawings, and project specificationsMeasure, cut, fit, and assemble piping accuratelyComplete pipe layout and fit up according to project requirementsInspect completed work for quality, accuracy, and code complianceCoordinate with crew members and supervision to maintain project schedulesMaintain a safe, clean, and organized work areaFollow all site specific safety requirements and procedures

Pipefitters Needed | Data Center Fitting Project | Richmond, VirginiaKodiak is seeking experienced Pipefitters at the Journeyman and Helper levels for a data center fitting project. We are looking for dependable craftsmen with experience fitting carbon steel and stainless steel pipe who take pride in producing accurate, high quality work. Both local and traveling candidates are encouraged to apply.This position is mainly bolt up work on prefabricated piping items. Candidates will read fabrication drawings, assemble pre-fabricated pipe spools, perform precision fit up, and ensure all assemblies are plumb, level, and square. Candidates should be comfortable working in a data center environment and possess strong layout and fabrication skills.ResponsibilitiesRead and interpret piping isometric drawings and fabrication blueprintsFit and assemble carbon steel and stainless steel piping systemsMeasure, lay out, and align piping components to specificationAssemble pre-fabricated pipe spools while maintaining proper dimensions and fit upVerify all assemblies are plumb, level, and squareMaintain proper weld gaps and prepare assemblies for weldingInstall and align flanges, elbows, tees, reducers, valves, and other piping componentsPerform quality checks to ensure assemblies meet drawing specificationsMaintain a safe, clean, and organized work area

NOW HIRING: Safety ProfessionalLocation: WisconsinStart Date: ASAPNCW is seeking an experienced Safety Professional to join a long-term project.If you have 4+ years of safety experience and a passion for keeping teams safe, we want to hear from you!

NOW HIRING: MIG PULSE WELDERS - Minneapolis, MNNCW is hiring Assembly Welders for a 2-month project - with more work after completion of project!Job Details:MIG Pulse Welding1/4" steel.035 wireFixture workAssembly welding

Trillium Construction is seeking Stick Welders near Falmouth, MI to perform welding on carbon steel piping using a WPS-SMAW-F3-F4-P1 welding procedure, which utilizes Shielded Metal Arc Welding (SMAW).This work will be performed both above ground and below ground in trenches. Welders will also be welding stainless steel piping using our WPS-WFS-GTAW-P8 welding procedure, which utilizes Gas Tungsten Arc Welding (GTAW). Stainless steel welding activities will be performed above ground.

Job OverviewKodiak Labor Solutions is seeking Plumbers at the Journeyman and Helper levels for a data center construction project in Richmond, Virginia running 6+ months. Both local and traveling candidates are encouraged to apply.What You'll DoInstall, assemble, and support copper ProPress and PVC piping systemsPerform ProPress connections on copper pipingInstall water, gas, and drainage piping systems as requiredRead and interpret blueprints, mechanical drawings, and project specificationsMeasure, cut, fit, and assemble piping accuratelyComplete pipe layout and fit up according to project requirementsInspect completed work for quality, accuracy, and code complianceCoordinate with crew members and supervision to maintain project schedulesMaintain a safe, clean, and organized work areaFollow all site specific safety requirements and procedures

Job OverviewKodiak Labor Solutions is seeking experienced Sheet Metal Mechanics at the Journeyman and Helper levels for a large scale commercial data center project in the Richmond, Virginia area.Both local and traveling candidates are encouraged to apply. This is a 6+ month opportunity for sheet metal professionals with hands on experience fabricating, installing, and hanging commercial ductwork.What You'll DoAs a Sheet Metal Mechanic, you'll work as part of an active construction crew installing and supporting ductwork systems throughout the data center project.Responsibilities IncludeFabricate, install, and hang sheet metal ductwork according to project drawings and specificationsRead and interpret mechanical drawings, blueprints, layouts, and installation documentationMeasure, fit, and assemble ductwork and related sheet metal componentsCoordinate with crew members and supervision to maintain installation schedules and project timelinesMaintain tools and equipment in accordance with jobsite and safety standardsFollow all site specific safety procedures and requirementsCommunicate installation issues, delays, and progress to the crew lead or foreman